Desk CAN Pro and Lab CAN Pro Technical Specifications

Both SeRoSys dongles share the same CAN engine: two independent channels, CAN 2.0A, CAN 2.0B and CAN FD to ISO 11898-1, 1 microsecond timestamps and a one-million-message ring buffer. The difference between them is what happens away from the PC. Desk CAN Pro is a bench and desk interface. Lab CAN Pro adds standalone logging to micro-SD, D-SUB power, automotive-grade GPIO, bus playback and a Qwiic port for peripherals.

Every figure below is from the product datasheets. Where a feature is not available, the table says so rather than leaving a blank.

At a glance

Desk CAN ProLab CAN Pro
Price (MSRP)$389.00$495.00
SKUSTDCP10STLCP10
CAN channels2 independent2 independent
CAN FD data phaseUp to 10,000 kbit/sUp to 10,000 kbit/s
Logs without a PCNoYes, to micro-SD
GPIONo2 in, 2 out, automotive grade
Powered from the busNo, USB onlyYes, +7 to +28 VDC via D-SUB
Qwiic peripheral portNoYes
Operating systemWindows 10 or laterWindows 10 or later
Best forDesk and bench analysisVehicle, rig and unattended testing

CAN interface

Identical on both models.

SpecificationDesk CAN ProLab CAN Pro
Channels2 independent2 independent
ProtocolsCAN 2.0A, CAN 2.0B, CAN FD (ISO 11898-1)CAN 2.0A, CAN 2.0B, CAN FD (ISO 11898-1)
Arbitration bit rateUp to 1,000 kbit/s per channelUp to 1,000 kbit/s per channel
CAN FD data phaseUp to 10,000 kbit/s (bit rate switch, x10)Up to 10,000 kbit/s (bit rate switch, x10)
Timestamp resolution1 microsecond1 microsecond
Receive buffer1,000,000 message ring buffer1,000,000 message ring buffer
Bus terminationChannel Independent software configurableChannel Independent software configurable
Listen-only (silent) modeYesYes
Standalone sendingYes, with no PC connectedYes, with no PC connected

Connectors, power and protection

SpecificationDesk CAN ProLab CAN Pro
ConnectorsMale + female pass-through DB9 on channel A, CiA® 106 pinoutMale + female pass-through DB9 on channel A, CiA® 106 pinout
USB powerYesYes
Power over D-SUBNoYes, in addition to USB
D-SUB supply range—+7 V to +28 VDC (nominal ~12 VDC)
D-SUB power protection—Overvoltage, reverse battery, ESD and transients
USB protectionESD, overvoltage and transient protectionESD, overvoltage and transient protection
Status LEDsPower, connection, bus traffic and modePower, connection, bus traffic and mode

Logging, playback and triggering

SpecificationDesk CAN ProLab CAN Pro
Hardware loggingNo — software logging onlyMicro-SD card slot, logs with no PC attached; 8 GB card included
Bus playback—Replays recorded logs onto either channel
Triggered capture—CAN message triggered event
Log file importASC, BLF, TRC and SLSS formatsASC, BLF, TRC and SLSS formats
Data displayHex, decimal or binary plus ASCII in parallelHex, decimal or binary plus ASCII in parallel

For unattended recording in a vehicle, see the guides to standalone CAN logging and CAN log file formats.

GPIO (Lab CAN Pro only)

The Desk CAN Pro has no GPIO. On the Lab CAN Pro the I/O is automotive grade and protected on every pin.

SpecificationLab CAN Pro
Pin count2 inputs and 2 outputs
Input protection−28 VDC to +28 VDC
Output driveUp to 14 mA steady state at CMOS levels (0 V / 5 V)
Output overvoltage protectionTo 28 VDC
Short-circuit protectionOn all GPIO pins
Thermal protectionRegulator shuts down power on over-temperature

Peripherals and expansion

SpecificationDesk CAN ProLab CAN Pro
Qwiic (I²C) connectorNoYes
A2B loggingNoYes, with a Flextech AKT Pocket A2B Bus Monitor over Qwiic

The Qwiic port follows the SparkFun standard and is what makes synchronized A2B and CAN logging possible, with both buses merged onto one timestamped timeline. The Qwiic cable is sold separately.

Software and integration

SpecificationDesk CAN ProLab CAN Pro
Included softwareLifetime SLSS CANAnalyser licence, no subscriptionLifetime SLSS CANAnalyser licence, no subscription
Database decodingDBCDBC
Pass-through driverJ2534 pass-thru 04.04 with CAN FDJ2534 pass-thru 04.04 with CAN FD
Automation APIDocumented TCP/IP interface, with a Python classDocumented TCP/IP interface, with a Python class
Software languagesEnglish and GermanEnglish and German
Operating systemWindows 10 or later; automate from macOS or Linux over the TCP/IP APIWindows 10 or later; automate from macOS or Linux over the TCP/IP API

Environmental and mechanical

SpecificationDesk CAN ProLab CAN Pro
Operating temperature−40 °C to +85 °C−40 °C to +85 °C
Enclosure ratingIP40 plasticIP40 plastic

Which one should you choose?

If the dongle will sit on a desk next to a PC running SLSS CANAnalyser, the Desk CAN Pro does everything the Lab model does on the CAN side — same channels, same bit rates, same timestamps, same buffer.

Choose the Lab CAN Pro when the test has to run without a laptop, when you need to power the dongle from the vehicle rather than USB, when you want to trigger on or drive external signals through GPIO, or when you need A2B logging over Qwiic.

For a side-by-side against PEAK, Ixxat and Vector, see the competitor comparison. The product lineup page has the shorter overview.

Datasheets

Full datasheets are on the datasheets page: Desk CAN Pro datasheet and Lab CAN Pro datasheet (PDF). Software manuals are on the downloads page.

Frequently asked questions

What CAN FD bit rate do these support?

Up to 1,000 kbit/s in the arbitration phase and up to 10,000 kbit/s in the CAN FD data phase, using the bit rate switch, on both models and on both channels.

Are the channels really independent?

Yes. Both models have two independent CAN channels that can run at different bit rates at the same time.

Can I use them without installing SLSS CANAnalyser?

Yes. The Desk CAN Pro and Lab CAN Pro both ship with a J2534 pass-thru 04.04 driver with CAN FD support, so they work with Windows OEM diagnostic and reprogramming tools. There is also a documented TCP/IP API for automation.

Does SLSS CANAnalyser run on macOS or Linux?

SLSS CANAnalyser is a Windows desktop application and needs Windows 10 or later, so the graphical tool itself runs on Windows. Both Desk CAN Pro and Lab CAN Pro are still usable from macOS and Linux through the documented TCP/IP automation interface, which exposes the same capture, transmit and logging functions to a Python script on any platform. Lab CAN Pro also logs to micro-SD without a PC attached at all, so you can record on any bench and analyse the file later.

Is there a subscription or annual licence fee?

No. The SLSS CANAnalyser licence is included with the hardware and is for life. There is no recurring fee.

Which model logs to an SD card?

The Lab CAN Pro only. It has a micro-SD slot and records with no PC attached; the Desk CAN Pro logs through the software to the PC.

Can I replay a recorded log back onto the bus?

Yes, on the Lab CAN Pro, onto either channel.

Shopping Cart
Scroll to Top